U-section matrix
List every target width, height and return dimension. Request written tooling coverage for the agreed steel and thickness at each size.
Decking, Panel & Structural Machines
HSU-150 Solar U-Channel Roll Forming Line
A multi-size U-section line for solar mounting components. Match your rail drawing and punch schedule to the offered HSU-150 before comparing output claims.
Our Xiamen production base describes a single-U reference family with 70–150 mm published web width, 30–70 mm section height and 2.0–3.5 mm material thickness. These are catalogue limits for a family, not proof that every width, height, steel grade and hole pattern can be combined in one quoted build. Supply the approved section, steel grade, thickness range, punching layout and target output for review.
Drawing basedprofile and tooling
HSU-150model family
PLC controlledproduction recipes
Our Xiamen production base's catalogue visualization, not a photograph of the offered build. Confirm the current machine and trial parts before purchase.
HSU-150 selection
Verify U-section changeover and hole positions
This page addresses a multi-size U-channel decision, distinct from HSM-41's compact 41.3 mm-base strut channel.
Changeover record
Ask the supplier to demonstrate a size change using the offered controls and record the settings and first acceptable part.
Punch registration
Use a revision-controlled hole and slot layout. Measure centres, edge distances and repeat pitch on identified samples after a size change.
Output conditions
Record coil grade, thickness, part length and hole density during the run. A catalogue speed is not an order-specific shift output.
Profile and material range
Technical specification framework
Values below separate confirmed product information from project-dependent engineering data.
- Model / family
- HSU-150
- Published profile family
- Single-U multi-size solar mounting profiles
- Web width
- 70-150 mm
- Profile height
- 30-70 mm
- Thickness
- 2.0-3.5 mm
- Published speed
- Up to 35 m/min
- Length / hole-position accuracy
- +/-1 mm published reference
- Control
- Industrial PC, intelligent controls and USB / network data transfer
- Other profile families
- Our Xiamen production base mentions C, Z and C/Z equipment in the broader family; request separate tooling and a written scope before attributing those shapes to this HSU-150 quotation
- Final guaranteed values
- Issued after drawing, material and production-cycle review
- Size-change proof
- Witness settings, time, first-off section and hole measurements for two agreed U sizes
- Punching scope
- Confirm tooling for the buyer's complete slot schedule, not only a single sample hole
- Electrical standard
- Configured for destination voltage, frequency and components
- Length and tolerance
- Guaranteed in the signed technical agreement
Source and boundary: family dimensions, thickness, control route and reference speed are from our Xiamen production base's SU-series product description, checked 26 September 2026. Its speed and accuracy figures are published references, not verified results for your material or hole density. The signed technical agreement and measured trial govern the final values. Reviewed by Halcyon Machinery on 26 September 2026.
Witnessed trial
Prove two U sizes with the same ordered line
Agree the test coil, two drawings and acceptance points before the run.
Identify coil
Run first U size
Measure holes and section
Record changeover
Run second U size
Check first-off fit
Equipment details & factory reference
Review the proposed configuration before production
We provide the current machine layout, component list, sample profile and test plan for the exact quotation.
HSU-150 Solar U-Channel Roll Forming LineCatalogue visualization, not a trial photograph. Request current build footage and measured samples for the offered machine.
Reference configurationQuotation boundaries
Ask what the multi-size proposal covers
Separate the published model family from the equipment and tooling in a specific order.
Profile table
Give every U-section size, flange return and tolerance in a drawing matrix. Mark mandatory and optional sizes.
Material envelope
Confirm steel grade, yield range, coating, thickness and coil dimensions for each section.
Hole tools
Identify slots, round holes, pitch and edge distances; request a sample from the offered die set.
Recipe transfer
Our Xiamen production base describes industrial-PC control and USB or network import. Confirm file format, revision handling and changeover records.
Run evidence
Measure section and hole location at two selected sizes, with coil identity and trial time recorded.
Delivery scope
List coil handling, cut-off, run-out, guarding, electrical standard and commissioning responsibility.
Related buyer decisions
HSU-150 and HSM-41 answer different solar-profile questions
Choose HSU-150 only after confirming the multi-size U-section range. A compact strut-channel drawing may point to HSM-41 or another tool set.
FAQ
Before buying a multi-size U line
Does HSU-150 automatically cover C and Z profiles?
No such capability should be inferred from the HSU-150 name. Ask for the exact ordered tooling, supported drawings and separate C/Z trial evidence if needed.
How do we verify a size change?
Record the starting and target U drawings, settings, elapsed changeover and the measured first acceptable part at both sizes.
Does the published speed represent output with our holes?
No. Output depends on coil, slot density, part length, cut-off and handling. Agree a trial or cycle calculation for the actual order.
Send your drawing for a matched proposal
We will confirm the suitable model, process route, line modules and the values that can be guaranteed for your material.
- Dimensioned profile drawing
- Material grade and thickness
- Hole pattern and finished lengths
- Target output per shift
- Power supply and destination country
Recheck hole datums after a U-section size change
Hole pitch, transverse location and cut-end offsets answer different acceptance questions. Use the U-channel size-change hole-datum guide to connect each drawing to identified first-off and later samples.