Section fit
Match base, web height, lip return and material thickness to the approved solar strut channel drawing. Do not treat a list of available sizes as a tolerance report.
Decking, Panel & Structural Machines
Strut Channel Roll Forming Machine – HSM-41 (41 mm Unistrut-Type)
Direct answer: the HSM-41 is our strut channel roll forming machine for 41 mm (1-5/8") Unistrut-type channels used in solar mounting, electrical and pipe supports. It forms the channel in 25 stages and punches slots and cuts to length on the fly. Built in our Xiamen factory; send your channel drawing and slot layout for a quotation within 24 hours.
The published HSM-41 reference shows a 41.3 mm channel base and four listed web heights. Those are catalogue references, not proof that every requested height, lip, slot and thickness combination can be produced in one quoted build. Send a dimensioned profile drawing, steel grade, thickness range, punching layout and target output for a supplier-specific review.
Drawing basedprofile and tooling
HSM-41model family
PLC controlledproduction recipes
Our Xiamen production base's catalogue visualization, not a photograph of the offered build. Match the quoted machine and trial sample to your approved drawing.
HSM-41 buyer checks
Decide by the solar channel and its slots
Four checks turn a catalogue model name into a comparable production proposal.
Mounting-hole layout
Mark slot dimensions, centre distances, edge distances and repetition on one drawing revision. Ask for measured first-off pieces from the intended punch tooling.
Running method
Our Xiamen production base describes synchronized flying punching and cutting on its HSM-41 reference. Confirm which operations and handling modules are included in the exact quotation.
Acceptance sample
Witness a trial with the agreed steel and profile. Record channel dimensions, slot placement and cut length against the signed acceptance method.
Profile and material range
Technical specification framework
Values below separate confirmed product information from project-dependent engineering data.
- Model / family
- HSM-41
- Published dimensions / weight
- 16.29 x 1.46 x 1.5 m / 12.5 t
- Drive power
- 30 kW
- Hydraulic power
- 15 + 7.5 kW
- Forming stages
- 25
- Published line speed
- 35 m/min
- Profile width
- 41.3 mm
- Profile heights
- 20.63 / 41.3 / 61 / 82.6 mm
- Lip
- 9.5 mm and 7.2 mm
- Thickness
- 1.0-2.5 mm
- Drive / control
- Chain drive / PLC
- Final guaranteed values
- Issued after drawing, material and production-cycle review
- Published process route
- Synchronized flying punching and flying cutting; confirm included tooling and limits for the offered build
- Slot pattern and production output
- Confirm by the buyer's drawing, punching density and witnessed run
- Electrical standard
- Configured for destination voltage, frequency and components
- Length and tolerance
- Guaranteed in the signed technical agreement
Source and boundary: model figures are from the HSM-41 catalogue, checked 26 September 2026. Its line-speed figure describes a published reference, not verified output for your steel, hole density or shift. The signed technical agreement and measured trial govern guaranteed values. Reviewed by Halcyon Machinery on 26 September 2026.
Trial sequence
Follow the channel from coil to fitted sample
Use one approved drawing revision and identify the coil used in the witnessed run. Our Xiamen production base's published HSM-41 layout places flying punching after forming and before flying cutting. The sequence below follows that reference layout; confirm the station order and included operations for the actual offered build.
Identify coil and grade
Set channel and guides
Form the lips and web
Check flying-punch slots
Check flying-cut length
Measure and fit sample
HSM-41 trial evidence
Record the channel and slot measurements on an identified sample
The catalogue image above is a machine visualization. It does not show a measured HSM-41 production trial. Ask for a sample record tied to your approved drawing, material and quoted tooling.
- Channel width and height
- Measure the approved 41.3 mm reference width and each height actually included in the quotation; do not assume every catalogue height is supplied.
- Lips and formed edges
- Compare both lip dimensions and the formed edge condition with the signed section drawing.
- Holes and slots
- Record slot shape, centre spacing, edge distance and any punching variation on identified pieces.
- Cut length and fit
- Measure finished lengths and trial-fit the channel with the intended connectors and assembly drawing.
- Cycle and output
- Record the actual hole density, piece length and timed run; the published line speed alone does not establish saleable output.
Decision boundary: the HSM-41 catalogue supplies reference profile dimensions. Acceptance tolerances and guaranteed output must be agreed for the offered build and witnessed material. Reviewed by Halcyon Machinery on 28 September 2026.
Quotation boundaries
Ask what the HSM-41 offer actually includes
Price, output and acceptance are only comparable when these interfaces are defined.
Input material
State steel grade, yield range, coating, thickness and coil dimensions. Ask whether the listed profile heights are supported with that material.
Hole and slot tooling
Supply the full mounting-hole schedule and identify any slots that require separate tooling or a revised operation sequence.
Flying operations
Confirm the offered punching and cut-off equipment, minimum piece length and production assumptions for the actual slot density.
First-off evidence
Specify which channel dimensions, hole centres, edge distances and cut lengths will be measured on trial pieces.
Handling and controls
List decoiler, run-out and stacking scope, PLC recipe transfer and required production records in the proposal.
Installation package
Confirm destination power, guarding, drawings, manuals, spare parts and commissioning responsibilities before order approval.
Related buyer decisions
Compare the channel, not just the machine names
HSM-41 is a specific strut-channel reference. A different solar rail or bracket drawing may call for different tooling or another line.
FAQ
Questions before selecting HSM-41
Are all catalogue channel heights included in one quotation?
Not automatically. Send each approved cross-section and material range; request a written tooling matrix for the exact HSM-41 build.
Does the published 35 m/min include my slot pattern?
Our Xiamen production base lists a reference line speed. Output with your hole density and cut length needs a witnessed trial or agreed cycle calculation.
What proves the channel is fit for my mounting assembly?
Measure the section and slots on identified trial pieces, then check fit with the intended connectors and assembly drawing. Structural certification is a separate project requirement.
Send your drawing for a matched proposal
We will confirm the suitable model, process route, line modules and the values that can be guaranteed for your material.
- Dimensioned profile drawing
- Material grade and thickness
- Hole pattern and finished lengths
- Target output per shift
- Power supply and destination country
Strut channel roll forming machine FAQ
What is a strut channel roll forming machine?
It is a roll forming line that forms steel coil into a C-shaped strut channel with turned-in lips, punches the slot pattern and cuts each piece to length. Strut channels (often called Unistrut-type channels) carry solar panels, cable trays, pipes and electrical equipment.
Which strut channel sizes can the HSM-41 make?
The published HSM-41 reference has a 41.3 mm channel base with four listed web heights. Your exact height, lip, slot pattern and thickness are confirmed on your drawing before we quote.
Can it punch slots and cut without stopping?
Our HSM-41 reference uses synchronized flying punching and cutting. Confirm the punching tools, slot pattern and handling modules included in your quotation and witness a trial with your coil.
How much does a strut channel roll forming machine cost?
Strut channel lines are quoted per project because the slot pattern, punching method and automation change the price. Send your channel drawing and target output and we reply within 24 hours.
Unistrut is a trademark of its owner; "Unistrut-type" describes the common 41 mm strut channel format.